Search results

This study aimed to determine the peak impact force and force attenuation capacity of weft-knitted spacer fabrics intended for padding that can be used for human body protection against impact.

A total of five weft-knitted spacer fabrics were fabricated with four different diameters of nylon monofilament yarns and one doubled monofilament yarns, respectively. The impact performances of the weft-knitted spacer fabrics were tested using a drop test method with a customized test rig to simulate falling. Impact tests were conducted on single- and multilayered experimental spacer fabrics to investigate the peak impact force and force attenuation capacity.

It was found that weft-knitted spacer fabric with a coarser or larger diameter of monofilament spacer yarn generated lower impact force and higher force attenuation capacity, thus resulting in better impact performance. Greater force attenuation can be achieved by utilizing a higher number of spacer fabric layers. However, the increase in thickness must be considered with the spacer fabric end use.

This study employed relatively coarse nylon monofilament yarn as spacer yarns to gain knowledge on the impact performance of weft-knitted spacer fabrics compared to warp-knitted spacer fabrics which are more common. The results showed that the diameter of spacer yarn significantly influenced the impact performance of the experimental weft-knitted spacer fabrics. These results could be useful for designing and engineering textile-based impact protectors.

The purpose of this study is to analyse the characteristics of cellulose fibres derived from the pseudo-stems of Curcuma longa and to evaluate the properties of non-woven fabric produced using these fibres.

The fibres were extracted via a decortication method. The acquired intrinsic qualities of the fibres were used to assess the feasibility of using them in textile applications. The thermal bonding approach was used for the development of the non-woven fabric, using a hot press machine with low-melt polyester fibre as a binder.

The mean length of Curcuma longa fibres was determined to be 52.73 cm, with a fineness value of 4.00 tex. The fibres exhibited an uneven cross-sectional morphology, characterized by a diverse range of oval-shaped lumens. The fibre exhibited a tenacity of 1.45 g/denier and an elongation value of 4.30%. The fibres possessed a moisture regain value of 11.30%. The experimental non-woven fabrics had consistent weight and thickness, while exhibiting different properties in terms of tensile strength and air permeability, with Fabric C having the highest tensile strength and the lowest air permeability value.

The features of Curcuma longa fibre, obtained with the decortication process, exhibited suitability for textile applications. Three experimental non-woven fabrics comprising different compositions of Curcuma longa fibre and low-melt polyester fibre were produced. The tensile strength and air permeability properties of these fabrics were influenced by the composition of the fibres.

The purpose of this study was to characterize the fiber from Curcuma longa (turmeric) stems. The fiber’s properties were used to assess its potential for textile yarn production.

The natural fiber used in this investigation was extracted from agricultural waste through a cold water-retting process.

The Curcuma longa fiber had a crystallinity of 50%. Cellulose, hemicellulose and lignin were detected in the fibers’ Fourier transform infrared spectra. A Curcuma longa fiber bundle contains several constituent fibers. The fibers exhibited an irregular cross-section, with a variable oval shape for the lumen. The fibers of Curcuma longa averaged 30.22 cm in length. The fineness of the fibers was 6.58 Tex. In this study, Curcuma longa fibers had an 11.30% moisture regain. The tensile strength of the fibers was 19.18 g/Tex. Curcuma longa fibers showed a break elongation of 9.79%. The fiber coefficient of friction was 0.3.

Curcuma longa has characteristics that make it appropriate for industrial uses like spinning. Thus, it is possible to use Curcuma longa fiber as a raw material for textiles.

The purpose of this study is to explore the potential of Cordyline Australis fibers as an alternate raw material for textile.

The water retting method was used to extract the fiber. Cordyline Australis fibers were characterized in terms of the morphology of fibers (fiber cross-sectional and longitudinal), fiber chemical functional groups, tensile strength and elongation, fineness, fiber length, moisture regain and friction coefficient.

Cordyline Australis fiber strands consist of several individual fibers. At the longitudinal section, the fiber cells appeared as long cylindrical tubes with a rough surface. The cross-section of the Cordyline Australis fibers was irregular but some were oval. The key components in the fibers were cellulose, hemicellulose and lignin. The tensile strength of the fiber per bundle was 2.5 gf/den. The elongation of fibers was 13.15%. The fineness of fiber was 8.35 Tex. The average length of the fibers was 54.72 cm. Moisture Regain for fiber was 8.59%. The friction coefficient of fibers was 0.16. The properties of the fiber showed that the Cordyline Australis fiber has the potential to be produced into yarn.

To the best of the author's knowledge, there is no scientific article focused on the Cordyline Australis fibers. Natural fibers from the leaves of the Cordyline Australis plant could be used as an alternate material for textile.

The purpose of this paper is to investigate the influence and relationship of segment area and opening area in segmented protective pad in comparison to non-segmented pad to the energy absorption and performance attributes relevant to thermophysiological wear comfort.

The compressive stress-strain curves were obtained using Instron Tester and were used to analyse the energy absorption of the pads and the segmented pad assemblies. The dry thermal resistance and evaporative resistance of the non-segmented and segmented protective pads were obtained using MTNW Sweating Guarded Hot Plate.

The compression test results and performance attributes relevant to thermophysiological wear comfort test result demonstrated that the area segment and opening area of segmented pad influenced their energy absorption value, dry thermal resistance value and evaporative resistance value (permeability index value).

The results are expected to be useful for design and engineering of hip impact protective garments. Hip impact protective pads are used to prevent hip fractures in elderly people as a result of fall.

This study aims to characterize the properties of natural cellulose fiber from the pseudo-stems of the curcuma zedoaria plant.

The fiber was extracted using the biological retting process (cold-water retting). The intrinsic fiber properties obtained were used to evaluate the possibility of using fiber for textile applications.

The average length of a curcuma zedoaria fiber was 34.77 cm with a fineness value of 6.72 Tex. A bundle of curcuma zedoaria fibers was comprised of many elementary fibers. Curcuma zedoaria had an irregular cross-section, with the lumen having a varied oval shape. Curcuma zedoaria fibers had tenacity and elongation value of 3.32 gf/denier and 6.95%, respectively. Curcuma zedoaria fibers had a coefficient of friction value of 0.46. Curcuma zedoaria fibers belong to a hygroscopic fiber type with a moisture regain value of 10.29%.

Extraction and Characterization of Curcuma zedoaria Pseudo-stems Fibers for Textile Application.

This paper aims to examine the influence of hip protective clothing on ensemble performance attributes related to thermal comfort. It also explores the effect on protective pads of various materials and the arrangements of material. The thermal comfort characteristics are thermal insulation and moisture vapour resistance.

For this research, four ensembles of clothing were used: one ensemble without hip protective clothing and three ensembles with hip protective clothing. A thermal manikin was used to test the thermal insulation and moisture vapour resistance of the ensembles.

The findings revealed that incorporating hip protective clothing into the clothing ensembles influenced the thermal resistance and moisture vapour resistance of the ensemble. In the “all zones group,” the influence of the hip protective clothing depended on clothing style, with hipster-style clothing producing insignificant changes. In the “hip zones group” and “stomach and hip zones group,” hip protective clothing strongly influenced the thermal comfort attributes of ensembles. Pad material and volume play important roles in these changes in thermal comfort attributes.

These outcomes are useful for the design and engineering of hip protective clothing, where maximizing protection while minimizing thermal and moisture vapour resistance is critical for wear comfort and adherence in warm or hot conditions. The designer should consider that material, volume and thickness of protective pad affect the overall thermal comfort attributes of the hip protective clothing.

This study aimed to evaluate the performance attributes relevant to thermal wear comfort of the commercially available hip protective pads and materials intended for impact protection that can be used for the hip protective pad.

The performance attributes relevant to thermal wear comfort (i.e. dry thermal resistance and evaporative resistance) of the pads were tested using MTNW Integrated Sweating Guarded Hotplate (iSGHP).

It was found that: the pad with more porous structure has more advantages in terms of evaporative resistance; the permeability index will be higher on the pad with an opening such as a segmented pad; the permeability index will be lower on the thicker and larger pad. The pocket fabric with open structure will have lower dry thermal resistance and evaporative resistance.

The study results showed that the properties of the utilised materials influenced thermal comfort performance. These results could be useful for designing and engineering hip protective garments.